Sony PD 170

POWER SWITCH - under the right thumb when the camera is hand held

The power switch has four positions….

1. Press in the small green button and then rotate the power switch to VCR. The camera should bleep and the transport controls illuminate - you can use the player/recorder to review your tapes by operating the STOP, REWIND, PLAY, FAST FORWARD and PAUSE buttons.
2. OFF (CHG) is obviously the power off position and used to save battery. You should also use this position when charging a battery.
3. Press in the small green button and then rotate the power switch to CAMERA. You should now see a picture.
4. MEMORY - select when recording information to the memory stick

NB -If you still cannot see a picture in the viewfinder check that you have removed the lens cap and then check that your battery has some charge in it.

INSERTING A TAPE

1. Press the small blue EJECT button inwards and then slide downwards.
2. Insert the tape
3. First close the inner cassette compartment first where it says PUSH
4. Finally close the outer cassette lid where it says PUSH
   

START / STOP - under the right thumb when the camera is hand held

This is a red button with the power switch control around it.

TO START RECORDING - Press the red button, the message REC will appear in the viewfinder

TO STOP RECORDING -Press the red button again, the message STBY will appear in the viewfinder.

NB when there is a tape in the camera it will automatically default to save mode after five minutes. You will still see a picture but it will take a few seconds longer to drop into record.

RECORDING STILL IMAGES

You may have to record still images for download onto a web page.

1. Press the silver PHOTO button (beside the zoom rocker) firmly. The camera will "blink" and record the still for seven seconds. Seven red markers will countdown the recording.
2. Pictures can also be recorded on a memory stick inserted into the camera.

POWER ZOOM

1. The 'T' stands for TELEPHOTO and will zoom the lens in.
2. The 'W' stands for WIDE-ANGLE and will zoom the lens out.

Press the zoom controller gently for a slow zoom speed and press harder for a faster zoom speed.

There is also a manual zoom ring (behind the focus ring) The zoom speed is controlled by the speed at which the ring is turned. Turn clockwise to zoom out and anticlockwise to zoom in.

AUTO LOCK

1. When the HOLD/AUTO LOCK switch is in AUTO LOCK position - the camcorder will automatically adjust the IRIS, GAIN, SHUTTER SPEED and WHITE BALANCE.
2. With the HOLD/AUTO LOCK turned to the middle position you have the choice of operating the above features manually or on auto
3. To retain the settings you have adjusted manually, turn the HOLD/AUTO LOCK to the HOLD position.

AUTO FOCUS

1. With the FOCUS switch set to AUTO the camera will automatically focus for you.
2. Set the switch to MANUAL to take control of focusing and appears in the viewfinder.
3. The PUSH AUTO button below will automatically focus the camera on whatever is in the centre of the picture. When you release the button it will revert to the manual mode.

STEADY SHOT

1. This is an optical means of compensating for camera shake.
2. You can switch it on/off with the STEADY SHOT in the menus.
3. When switched off - the      off     symbol appears in the viewfinder/LCD
4. It should be switched on in most circumstances because even lightweight tripods are inherently unstable.

EDIT SEARCH

1. Momentarily holding down the EDIT SEARCH rocker marked "-" allows you to look at the last two seconds of the last picture you recorded.
2. By holding down the "+" or "-" side of the edit search you can forward or rewind through the tape.

Be careful when you use the edit search facility. If you forward onto blank tape and start recording, there will be a break in time code - which will give you problems when you come to edit. Always cue up on the last recorded picture to ensure you have continuous timecode throughout your rushes. The END SEARCH function will help you do this…

The END SEARCH button will take you to the end of the last recorded section. The camera rewinds or fast forwards the tape until it finds the last picture frame - it will play the last five seconds of your pictures and park, ready to record.

THE LCD SCREEN

1. Once you pull out the LCD screen the viewfinder is automatically switched off.
2. However, both the Viewfinder and LCD will be on together when the screen is turned through 180 degrees
3. Once the LCD screen is re-housed into the side of the camera the viewfinder becomes operational.
4. When the screen is turned through 180 degrees (to do a piece to camera) it drops into "mirror mode".
5. From that screen position you can also push the screen flat against the camera – with the screen facing outwards. This may be useful when conducting an interview with the camera on a tripod.
6. You can adjust the brightness of the screen by using the LCD BRIGHT +/- controls on the left hand edge of the screen.
7. You can also adjust the cameras backlight brightness in the menus

NB in mirror mode a small cartoon face appears in the viewfinder (cute!).

Take care of the LCD screen….

1. Do not touch the surface of the screen
2. Do not lift the camera by the viewfinder or screen
3. Remember the LCD screen uses more battery power than the viewfinder. Revert to viewfinder only use, if battery power is running out.
4. Exposing the screen to sunlight for extended periods will damage it.